The Best 10in Subwoofer of 2023

Powerful 10" copper-spun front-firing woofer

All-digital amplifier delivers 300 watts of dynamic power

Equally impressive with music and movies

Low pass crossover and phase control,Dimensions:14(H) x 12.5(W) x 15.7(D) Inches

Line/LFE inputs for compatibility with most receivers

10-Inch Dual 4 ohm Shallow Mount Subwoofer

Peak Power: 800 Watts | RMS Power: 500 Watts

Shallow Mount Design - Mounting Depth: 4.41"

High Performance Pressed Paper Cone Stitched to Premium Foam Surround

Sensitivity: 85.1 dB | Fs: 41.9 Hz

POWERED SUBWOOFER FOR EXTRA BASS & PUNCH – A 10-inch Dynamic Balance woofer & a uniquely configured directed port provides accurate bass with added depth that brings your music and movies alive. A perfect solution for your small-to-mid size room

LOUDER CLEARER SOUND EVEN AT HIGH VOLUME – Enjoy a thrilling yet balanced music experience with rich, deep sound, even at low frequencies. BLENDS EASILY WITH ANY SPEAKER and plays the most demanding nodes effortlessly without any distortion

DOUBLE THE AMPLIFIER POWER TO 100 Watts of Dynamic Power with its in-built 50-watt RMS amp. Sophisticated engineering with best in class resonance-free driver materials make this sub highly durable and FIT FOR EXTENDED USE

EASY TO INTEGRATE WITH EXISTING SYSTEMS – Hook up this sub to the receiver and upgrade your music sound instantly! Features continuously variable 80-160 Hz crossover and 40-160 Hz (-3dB) frequency response

A sleek detachable grille on the front, speaker and line-level inputs as well as speaker-level outputs on the back, and a Phase Toggle Switch for multiple subwoofers, make this sub cohesive and complete!

Spun copper front-firing Cerametallic woofers

10-inch, front-firing driver

150 watts continuous, 300 watts dynamic power

Strong, flexible, removable grille

All digital amplifier for high-efficiency and true-to-source sound accuracy

Must be connected to AV Receiver, processor, or pre-amp

Contemporary finish to integrate with any decor with ease

Dimensions: 14” H x 12.5” W x 15.7” D

What’s in the box: (1) Sub-100 Subwoofer and power cord - connection wires not included

Place your subwoofer in a corner for optimal performance

Peak Power: 1, 600 Watts | RMS Power: 800 watts

2.6" (65.5mm) dual 4-ohm high temperature 4-layer copper Voice Coil

Powerful high flux ferrite motor with advanced air Flow Cooling Design | Fs: 45 Hz

Engineered for incredibly deep, dynamic, and powerful bass | Sensitivity: 83.5 dB

High Roll Foam Surround stitched to competition Grade pressed paper cone

Frequency response range: 28 Hz - 325 Hz | mounting depth: 6.04"

Universal Fit - Dual Chamber 10" Ported Subwoofer Enclosure

Competition Grade, High Performance Subwoofer Box | Engineered to Sound Incredible

Kerf (Rounded) Port Design - Allows for Deep, Accurate, and Responsive Bass

Internal Volume: 2.70 ft³ | Tuned @ 34 Hz

Subwoofer Hole Cut-Out Diameter: 9.125" | Mounting Depth: 9.5"

Premium Push Terminals with Internal Speaker Wire Leads Ready for Installation

SDR Series Single 10-Inch D2 ohm Loaded Subwoofer Enclosure

Peak Power: 1,200 Watts | RMS Power: 600 Watts

Pre-wired Internally for a 1 Ohm Final Impedance Load at the Terminals for an Easy Installation

Premium Vented Enclosure Made of 5/8" MDF and Finished in Black Carpeting

Double Front Baffle (1.25") with Countersunk Subwoofer Design for Flush and Attractive Appearance

Built-in amplifier: with a MOSFET power supply you get improved switching speeds, better performance with less power from the driver, lower gate-to-drain feedback capacitance, lower thermal impedance for higher switching frequencies

Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes above the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)

High level inputs: speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the LOPRO10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs

Low-Level Inputs - Line level inputs (RCA inputs / low-level inputs) use RCA interconnect cables to link the LOPRO10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers

Variable bass boost: variable bass boost allows you to adjust the low bass within the boost Range to just the way you like it

Dimensions: 15” x 9. 75” x 3”. If you are short on space, This is a great solution for you. The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles

: sound storm provides a powerful 3-year Platinum online dealer so long as the purchase is made through . We strongly encourage Professional installation of this product to ensure proper and safe functionality

Enclosure Type: bass reflex

Amplifier Type: Class AB

Amplifier power: 120 watts peak/ 60 watts RMS

Frequency response: 38hz-200hz; crossover frequency: 40hz-200hz

Driver: 10" Low Throw dynamic woofer with these inputs: L/R/LFE/speaker level

The Punch P300-10 is a self-contained all-in-one solution featuring a Punch 10” subwoofer in a custom sealed enclosure and is powered by a mighty 300 Watt amplifier

The system is all-inclusive, so you only need to run power, ground and a signal from the source to get this baby moving – Dimensions (Wedge H x W x D1 x D2): 13.3” x 18” x 8.9” x 5.9”

Featuring an adjustable 12db/Octave low pass crossover, built-in adjustable bass EQ, built-in 0°/180° phase switch and Remote bass level control included

Closed-loop design ensures optimum performance between woofer, amplifier and enclosure with easy integration in aftermarket or OEM audio systems using RCA or speaker level signals

Famous Rockford Fosgate build quality with a full 1-year warranty when purchased from an authorized Rockford Fosgate reseller