The Best Gasket Sealers of 2023

Excellent Replacement: Ideal replacement for your FoodSaver (TM) Vacuum Sealer foam gasket for models with either 1 or 2 gaskets. Installing a FoodSaver (TM) gasket replacement helps improve suction and vacuum sealing performance when Foodsaver gaskets have deteriorated

Returns Suction Back To Normal: Our 4 pack of replacement FoodSaver (TM) gasket fits all Food Saver V2200, V2400, V2800, V3000, V3200, V3400 and V3840 series models. Corresponds to FoodSaver (TM) part T910-00075. For those models with 2 gaskets, replace both at the same time for best results

Built To Perform At A Great Value: Our gaskets are made from a purpose-specific, tighly engineered foam blend to ensure the highest quality level. What's more, we provide you with a pack of four gaskets to ensure that you always have spares on hand and never have to forgo the use of your machine because the gasket is out of commission

Fits Most Models: Replacement for V2200 series (V2220, V2222, V2240, V2244, V2250 and others), V2400 series (V2420, V2430, V2431, V2432, V2433, V2440, V2450, V2460, V2461, V2470, V2480, V2490), V2800 series (V2820, V2830, V2835, V2840, V2841, V2860, V2865), V3000 series (V3020, V3040, etc.), V3200 series (V3240, V3250, etc.), V3400 series (V3420, V3425, V3430, V3431, V3440, V3460, V3461, V3485), V3800 series (V3810, V3815, V3816, V3817, V3820, V3825, V3835, V3840, V3845, V3850, V3860, V3880)

Note: This is an aftermarket replacement product meeting or exceeding the quality of OEM gaskets (based on in-house testing), produced by Impresa Products (TM). Not for use with non-FoodSaver (TM) vacuum sealers or FoodSavers (TM) with rubber gaskets

Stops block leaks

Seals cracked cylinder heads and blocks

Repairs blown head gaskets

Contains a combination of antifreeze compatible sodium silicate sealing liquid and various size gasket sealing particles which penetrate gaps & cracks and harden to permanently stop leaks.

Formulated for hi-temp applications, or heavy-duty use

Replaces almost any cut gasket, and coats pre-cut gaskets to increase reliability

Makes reliable 'formed-in-place' gaskets that resist cracking, shrinking and migrating

Temperature range of -65F to 650F intermittent

Suggested Applications: Valve covers, oil pans, timing covers, water pumps, thermostat housings, transmission pans

FIX THE SUCKING: If your FoodSaver is having a difficult time holding the vacuum while sealing, it's likely that you just need to replace your gaskets! FoodSaver recommends replacing them annually.

FOAM GASKETS: If you have 1 Foam and 1 Rubber Gasket, only replace your FOAM gasket. Don't remove the rubber gasket. If you have 2 foam gaskets, always replace both foam gaskets at the same time. Please see description for details on certain models.

WORKS WITH: V2200, V2400, V2800, V3000, and V3200 Series FoodSaver models. Also works with: GameSaver Deluxe Plus.

V2200 Series: V2200, V2220, V2222, V2235, V2240, V2244, V2250, V2254, V2260 -- V2400 Series: V2420, V2430, V2431, V2432, V2433, V2440, V2450, V2460, V2461, V2470, V2480, V2490 *** V2800 Series: V2820, V2830, V2835, V2840, V2860, V2865

V3000 Series (Lower Gasket Only): V3020, V3040 *** V3200 Series(Lower Gasket Only): V3230, V3240, V3245, V3250 *** GameSaver Deluxe Plus

Just Pour & Go – No Need for Expensive Head Gasket Repairs - The Safe and Easy Way to Fix a Coolant Leak

Fixes blown head gaskets, cracked heads and blocks

A permanent repair, guaranteed for the lifetime of the engine

Scientifically Tested - K-Seal is the only product to have been successfully tested by the equipment at Brighton University and classes as meeting the demands of ASTM D3147

If product did not seal head gasket leak, the system might be Over-pressurized, which causes back pressure and doesn't allow the product to reach the problem area, on this page below under Technical Specification is a PDF Guide with instructions to follow to complete the repair successfully

Reliable, fast-drying, all-purpose sealant dries to a highly tacky, non-brittle film; remains tacky indefinitely

Tacky paste for holding cut gaskets in place during assembly; helps seal cut gaskets

Resists gasoline, oil, antifreeze, axle lube, kerosene, propane and butane; sensor-safe

Temperature Range: -65°F to 500°F (-54°C to 260°C)

Suggested Applications: Valve covers, fuel pumps, carburetors, manifold gaskets; seals any rubber, cork, paper or composite gasket

Fit type: Vehicle Specific

This is a new set of 2 lubricating grease pads

Ideal for lubricating gaskets and o-rings

Makes it easier for replacement

Simply place gasket between foam pads and twist

Slow-drying, non-hardening brush-top sealant

Resists gasoline, oil and grease

Approved for use in aviation as well as automotive applications

Suggested Applications: Close-fitting machined surfaces, sealing hoses, solid gaskets

Temperature range of -65F to 400F

FIT PERFECTLY & WORK WELL: If your old sealers have deteriorated and weakened the vacuum, losing its suction. Replace the gaskets then you will make your vacuum sealer machine operates like new. Your machine will vacuum sealing again

FIT MOST SERIES: Our Replacement gasket fits all V2200, V2400, V2800, V3000, V3200, V3400 and V3800 series models. For those models with 2 gaskets, replace both at the same time for best results

INSTALLED EASILY: Easily slid right into the channel for the gaskets. Installing a gasket replacement helps improve suction and vacuum sealing performance when gaskets have deteriorated. Make the vacuum sealer sucks air much faster like new

4-PACK: Have a spare set of gaskets for the future. SAVE MONEY AND ENJOY LIFE

100% GUARANTEE: You will be satisfied with our replacement gasket, if you are unsatisfied, we will refund the money unconditional, just tell us directly

Easy Pour and Go Formula!

Permanently fixes head gaskets, engine blocks, cooling systems, and cylinder heads.

"Contains 3 unique technologies. Military-Strength Fibers create multi-layer repair over cracks with a web-like weave. Nanotechnology permanently fixes the smallest cracks and crevices. Cool-X Conditioner – lowers operating temperature as it circulates through cooling system."

Seals larger holes with less fluid loss than competitive products as proven by lab test (ASTM D6107)

Works with all antifreeze or plain water.