The Best Mechanical Miter Gears of 2023

Made of 45# steel with high wear-resistance,strong and durable.

Lower contact ratio between gears, higher load capacity.

It only can fit for 1.5 module gear,16 teeth,90 degrees,12mm Hole Diameter.

Suitable for used in agricultural equipment, textile machinery, printing machinery, Mechanical transmission, etc.

Note:1 to 1 bevel gear (only 1 to 1 match, can not match with other modules and other number of teeth)

Note: This product does not contain fixing screws.

Lower contact ratio between gears, higher load capacity.

Suitable for used in agricultural equipment, textile machinery, printing machinery, Mechanical transmission, etc.

Made of 45# steel, high wear-resistance,longtime use.

Note:1 to 1 bevel gear (only 1 to 1 match, can not match with other modules and other number of teeth)

Straight miter 90 degree mesh transmits mechanical power between perpendicular shafts

Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles

Molded polyoxymethylene for quiet operation, low friction and moisture absorption, and high resistance to heat and abrasion combined with the corrosion resistance, ductility at high temperatures, and low magnetic permeability of brass

Unhardened teeth for 1:1 gear ratio applications where hardness and strength are not needed to transmit torque and motion

Straight miter 90 degree mesh transmits mechanical power between perpendicular shafts

Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles

300 series stainless steel for resistance to corrosion and chemicals

Unhardened teeth for 1:1 gear ratio applications where hardness and strength are not needed to transmit torque and motion

Right hand spiral miter 90 degree mesh transmits mechanical power between perpendicular shafts

Spiral angle of 35 degrees better suits this spiral miter gear for higher speed and larger torque applications than straight miter gears

Low carbon steel (.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion

Hardened teeth for 1:1 gear ratio applications where hardness and strength are needed to transmit torque and motion

Bore has keyway and setscrew for use with keyed shaft

Made of high quality 45# steel ,high wear-resistance,longtime use.

Lower contact ratio between gears, higher load capacity.

It only can fit for 2module gear,20 teeth,90 degrees,Hole Dia 14mm.

Suitable for used in agricultural equipment, textile machinery, printing machinery, Mechanical transmission, etc.

Note:1 to 1 bevel gear (only 1 to 1 match, can not match with other modules and other number of teeth)

Straight miter 90 degree mesh transmits mechanical power between perpendicular shafts

Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles

High carbon steel for tensile strength and hardness

Straight miter 90 degree mesh transmits mechanical power between perpendicular shafts

Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles

Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability

Unhardened teeth for 1:1 gear ratio applications where hardness and strength are not needed to transmit torque and motion

Made of 45# steel with high wear-resistance, strong and durable.

Tapered Bevel Gear Wheel, 2 Modulus, 20 teeth,14mm hole diameter.

Widely use in conveying, agricultural equipment, textile machinery, printing machinery, automotive applications, etc.

Straight miter 90 degree mesh transmits mechanical power between perpendicular shafts

Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles

Low carbon steel (.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion

Unhardened teeth for 1:1 gear ratio applications where hardness and strength are not needed to transmit torque and motion