The Best Subwoofer Amplifier For Car of 2023

POWER: Maximum Power output of 200 Watts at 2 Ohms into two channels. Maximum power output of 100 Watts at 4 Ohms into two channels

HIGH LEVEL INPUTS: Speaker level inputs are commonly referred to as high-level inputs. Speaker level inputs will be used to connect the R1002 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs

LOW LEVEL INPUTS: Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the R1002 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers

VARIABLE INPUT GAIN CONTROL: The Variable Input Control allows the amplifier input to match the output signal from the head unit to achieve optimum performance when adjusted properly.

WARRANTY: BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon Dot Com

Power - 1100 Max x 1 @ 2 Ohms, 550 Max x 1 @ 4 Ohms

Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal

Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry

Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers

Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction

Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it

Variable Input Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier

Specs - Dimensions: 9.13” x 10.44” x 2.25”, Weight: 4.43 lbs., Speaker Impedance: 2 to 8 Ohm, THD @ RMS Output: 0.01%, S/N Ratio: 102 dB, Frequency Response: 9 Hz to 50 kHz, Fuse Quantity: 1 30 Amp ATO Blade

Warranty - BOSS Audio Systems provides a 6 Year Platinum Online Dealer Warranty for purchases through Amazon.Com. We strongly encourage professional installation of this product to ensure proper functionality

Wiring Kit - 30 Ft Speaker Wire, 20 ft. 8 GA Red Power Cable, 16 ft. 18 GA Blue Turn-On Wire, 3 ft. 8 GA Black Ground Cable, Competition Quality Fuse Holder with AGU Fuse

Wiring Kit Continued - 10 5/16" and 1/4" Ring Terminals, 6 ft. Split Loom Tubing, 3 Rubber Grommets, 20 4" Wire Ties, 20 ft. High Performance blue RCA (TRCA) Interconnect

Amplifier Power - 1100 Watts Max x 1 @2-Ohms, 550 Watts Max x 1 @4-Ohms

Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal

Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry

Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction

Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it

Specs - Dimensions: 9.1” x 10.4” x 2.3”, Weight: 4.4 lbs.

Warranty - BOSS Audio Systems provides a Powerful 6 Year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality

power: max power output of 1500 watts at 2 ohms into one channel. maximum power output of 750 watts at 4 ohms into one channel. this amplifier is designed to run your subwoofer(s) giving them the power that they need to perform as they were meant to

high level inputs: speaker level inputs are commonly referred to as high-level inputs. this input will be used to connect the ac1500.1m to your factory radio or aftermarket radio that does not have low-level (rca) inputs

low level inputs: line level inputs, also known as rca inputs or low-level inputs, use rca interconnect cables to link the ac1500.1m with the source unit. most aftermarket radios have multiple pairs of rca outputs that can connect to multiple amplifiers

low-pass crossover: a low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. a low-pass filter will primarily keep high notes out of your subwoofer(s)

variable bass boost: variable bass boost allows you to adjust the low bass within the boost range to just the way you like it

COMPLETE SOUND PACKAGE: Upgrade your cars sound system with this complete package that includes MTX 12 inch dual loaded car subwoofer, a sub enclosure, Planet Audio monoblock amplifier and a complete 8 gauge amp installation wiring kit

CAR SUBWOOFER: The MTX Terminator series subwoofer system includes 2 subs, sub enclosure and a car amp; Boasts 1200 watts max power and 400 watts RMS; Features rubber surround, polypropylene cone and a 2-inch aluminum single 4 ohms voice coil

SUBWOOFER BOX ENCLOSURE: This MTX enclosure features solid MDF construction and thick black carpet; Dimensions (H x W x D1 x D2): 14 x 29.69 x 13.5 x 11.13 inches

CAR AMPLIFIER: Planet Audio Amplifier delivers 700 watts RMS x 1 @ 4 Ohm, 1100 watts RMS x 1 @ 2 Ohm, 2500 watts RMS x 1 @ 2 Ohm max power, 1500 watt max power; Switchable input sensitivity: 100mV 2V or 2V 8V; Selectable bass boost (0 to +18dB); Signal to noise ratio: 102dB; Frequency response: 20 20KHz; Dimensions (H x W x L): 2.19 x 10 x 10 inches; Remote control included

INSTALLATION WIRING KIT: 20-foot 8 gauge red power cable; 1/4-inch gold plated ring terminal; 3-foot 8 gauge black ground cable; Number 10 gold plated ring terminal; 16-foot 18 gauge blue turn on wire; 20-foot high performance RCA interconnect; (3) Rubber grommets; 30-foot speaker wire; 5/16-inch Gold plated ring terminal; 6-foot split loom tubing; (20) 4-inch wire ties

Power - 500 Watts Max x 2 @2-Ohms, 250 Watts Max x 2 @4-Ohms, 1000 Watts Max x 1 Bridged @4 Ohms

Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers

Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal

Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry

Variable Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier

Variable Bass Boost - With Variable Bass Boost you have the control of exactly how much BASS you want to pump out to your subwoofer(s)

Bridgeable - Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels

Specs - Dimensions: 9. 5” x 10. 31” x 2. 25”, Weight: 6. 62 lbs.

- BOSS Audio Systems provides a powerful 6 year Platinum Online Dealer so long as the purchase is made through . We strongly encourage professional installation of this product to ensure proper and safe functionality

Built-in amplifier: with a MOSFET power supply you get improved switching speeds, better performance with less power from the driver, lower gate-to-drain feedback capacitance, lower thermal impedance for higher switching frequencies

Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes above the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)

High level inputs: speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the LOPRO10 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs

Low-Level Inputs - Line level inputs (RCA inputs / low-level inputs) use RCA interconnect cables to link the LOPRO10 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers

Variable bass boost: variable bass boost allows you to adjust the low bass within the boost Range to just the way you like it

Dimensions: 15” x 9. 75” x 3”. If you are short on space, This is a great solution for you. The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles

: sound storm provides a powerful 3-year Platinum online dealer so long as the purchase is made through . We strongly encourage Professional installation of this product to ensure proper and safe functionality